1000 "Single Pass"encodes to your specified bitrate or quality.\n"Two-pass 1st pass" gathers statistics for the 2nd pass.\n"Two-pass 2nd pass" uses 1st pass' statistics to encode at target file size or bitrate.
1008 Restrict the usage of MPEG-4 tools and limit the encoded bitrate such that bitstreams are compatible with hardware decoders.
1009 Higher settings give higher-quality results, at the cost of slower encoding.
1010 H.263 smooths the image whereas MPEG (slightly slower) sharpens.\nCustom lets you define your own matrix.
1011 Choose what you would like the avi to identify itself as
1012 Maximum number of frames allowed between I-frames
1013 Turns on Lumi masking - applies more compression to dark/light areas that the eye can't notice easily
1014 Minimum quantizer allowed for I-frames. Only functional in 2-pass second pass.
1015 Maximum quantizer allowed for I-frames. Only functional in 2-pass second pass.
1016 Minimum quantizer allowed for P-frames.
1017 Maximum quantizer allowed for P-frames.
1018 Minimum quantizer allowed for B-frames, BEFORE ratio/offset scalling
1019 Maximum quantizer allowed for B-frames, BEFORE ratio/offset scalling
1020 Define your own MPEG quantization matrices. Quantization type must be set to "Custom" to affect encoding.
1021 A value of 20 will give 20% more bits to every I-frame
1022 If keyframes are close together, it might be useful to decrease the bitrate of all keyframes except the last one.\nUse this to define how close must keyframes be to be reduced.
1023 Check this if you would like to skip the storage of the 1st pass output. It is often very large.
1025 The higher this value, the more bits get taken from frames larger than the average size, and redistributed to others
1026 The higher this value, the more bits get assigned to frames below the average frame size
1030 Location for 1st pass stats file to be saved to
1031 Location for 2nd pass curve stats to be loaded from
1051 Enable XviD's internal CPU detection
1052 Override XviD's internal CPU detection (not recommended)
1059 Load a pair of custom intra/inter matrices
1060 Save the current intra/inter matrices to a file
1203 Encodes frames as interlaced - only use if your source contains interlacing artifacts (i.e. fields instead of progressive frames)
1204 How much of the overflow the codec can eat into during oversized sections\nLarger values will prevent oversized files better, but will also spoil quantizer distribution more.
1205 Maximum number of sequential B-frames.
1207 Ratio used to calculate the b-frame quantizer.\n\nBVOP quant = (AVG(past VOP quant, future VOP quant) * quant ratio + quant offset)
1210 How much of the overflow the codec can eat into during undersized sections.\nLarger values will prevent undersized files better, but will also spoil quantizer distribution more.
1212 Determines how slowly it will adjust the current encoding quality based upon scene intensity - this has the strongest influence on quality
1213 Determines how slowly it adapts to the current adjusted quality
1214 Provides said number of frames worth of buffer between the adjusted encoding quality and lowest possible quality
1215 When enabled the P-frames and B-frames are packed together in the one bitstreams. This permits decoding without delay.\neg. [I] [PB] [B] [empty] [PB] [B] [empty] [P]\n\nPacked bitstreams were introduced in DivX 5.01.
1224 Frame dropping ratio. 0 = no frame dropping .. 100 = drop all frames.
1227 Reduction of bitrate for the first consecutive i-frames. The last i-frame will get treated normally.
1231 Use Global Motion Compensation.
1232 Use Quarter PixEL resolution for encoding for a more precise motion compensation
1233 Use chroma information to detect motion (slower).
1234 B-frame quantizer offset from last p-frame quantizer; refer to b-frame quant ratio (above)
1238 VHQ enables an additional search process to increase quality (much slower).
1239 Interpolates colours in bright/dark areas for achieving a nicer edge impression
1258 Restrict the usage of MPEG-4 tools and limit the encoded bitrate such that bitstreams are compatible with hardware decoders.
1262 Change the amount of b-frames in this zone. Recommended values are between -20 (almost no b-vops) and 30 (many b-vops).\nThe hardcoded maximum in profile/level will never be exceeded
1266 Closes every group-of-pictures before encoding new keyframe.
1274 Change quality of this zone relative to other zones. It's not recommended to go below 0,2
1278 Fix this zone's quality to desired quant
1279 Don't code colour information in this zone. You also have to force a keyframe, or old colour information will stay
1293 Restrict the usage of MPEG-4 tools and limit the encoded bitrate such that bitstreams are compatible with hardware decoders.
1294 Suggested VOP width (pixels)
1295 Suggested VOP height (pixels)
1296 Suggested VOP rate (frames-per-second)
1297 Video Memory Verifier (VMV):\n\nThe maximum number of macroblocks permitted per VOP.
1298 Video Complexity Verifier (VCV):\nThe maximum macroblocks decoded per second.
1299 Video Buffer Verifier (VBV):\n\nThe maximum size of the video decoder buffer. The encoded bitstream but not overflow or underflow this buffer.
1300 Maximum instantaneous bitrate.
1302 The target AVI bitrate, file size, or quantizer.
1305 Change the amount of b-frames in this zone. Recommended values are between -20 (almost no b-vops) and 30 (many b-vops).\nThe hardcoded maximum in profile/level will never be exceeded
1306 Advanced, high quality quantization mode
1307 Toggle between quantizer, target bitrate, target file size
1341 Force a keyframe at the beginnig of the zone
1347 Enables special motion estimation features for cartoons/anime.
1349 0=Default from core (let xvid decide). Else overflow payback percent per frame. Higher value will meet target file size better, but will also spoil quantizer distribution more.
1351 Display aspect ratio is used to scale the video on playback/anamorphic encoding).\n\nDefault 1:1 for no scaling necessary.
1369 Faster motion estimation for b-frames and quarterpel
1375 Target file or media size
1376 The file size of subtitles or other data files
1377 Select file size from existing subtitle file
1379 Calculated container format overhead (kbytes).
1384 Calculated average video bitrate (kilobits-per-second)
